Amish made hardwood
It is currently Wed Dec 25, 2024 9:09 am

View unanswered posts | View active topics


Board index » Hardwood Flooring » General Hardwood Flooring

All times are UTC - 5 hours




Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 
  Print view Previous topic | Next topic 
Author Message
mswhite60
 Post subject: Removing/replacing particle board prior to 3/4" hardwood
PostPosted: Tue Jan 02, 2018 2:02 pm 
Offline
Newbie Contributor

Joined: Sun Dec 03, 2017 8:23 pm
Posts: 17
Hello all,

I have a house built in 1980 that has only 3/4" particle board subfloor. Sanity checking my plan.

The joists run EW, subfloor 4x8 sheets run NS.

I plan to:

1. Remove the PB and replace with 3/4 x 4 x 8 Tongue-and-Groove Plywood Sturd-I-Floor panels.
2. Lay down felt or underlayment paper,
3. Then the new hardwood would run NS across the subfloor and the EW joists.

Sound correct?

Pics - I was surprised that I had ONLY the 3/4" PB subfloor!

Image
Image
Image

Thanks!

Matt
Top
 Profile E-mail  
 
mswhite60
 Post subject: Re: Removing/replacing particle board prior to 3/4" hardwood
PostPosted: Tue Jan 02, 2018 2:16 pm 
Offline
Newbie Contributor

Joined: Sun Dec 03, 2017 8:23 pm
Posts: 17
OK - I just re-read the sticky and noticed something I missed earlier:

Quote:
There are other, older and not used anymore subfloor systems one may encounter. Such as: 1&1/8" T&G plywood subfloor installed at 90 deg to 4x6 beams spaced 4' oc.
1&1/2" x 5" T&G solid fir deck boards installed at 90 deg. to 4 x6 beams spaced 4' oc.
1x8 solid fir/pine boards installed at 90 deg to joists spaced 16" oc
1" RED-X T&G particle board subfloor installed at 90 deg to joists spaced 2' oc.
3/4" or 5/8" particle board found mostly today in modular and mobile homes.
These subfloors should NOT be removed but overlayed with 1/2" CDX plywood that is well stapled (2" around perimeter and 6" oc.) or glued or screwed. In all cases, subfloors and underlayments are to be flat to within 3/16" in a 10' radius.


So Am I better off just installing the 1/2" CDX over the existing PB?
Top
 Profile E-mail  
 
mswhite60
 Post subject: Re: Removing/replacing particle board prior to 3/4" hardwood
PostPosted: Tue Jan 02, 2018 5:32 pm 
Offline
Newbie Contributor

Joined: Sun Dec 03, 2017 8:23 pm
Posts: 17
Update: Because I see conflicting information all over the net regarding particleboard subfloor removal, I decided to speak to the manufacturer.

They said ABSOLUTELY DO NOT put 1/2" CDX over particle board subfloor and that it must be removed. I know this conflicts with Gary's info in the sticky.
Top
 Profile E-mail  
 
floormeintucson
 Post subject: Re: Removing/replacing particle board prior to 3/4" hardwood
PostPosted: Thu Jan 04, 2018 10:35 am 
Offline
Prized Contributor

Joined: Sat May 02, 2009 3:45 pm
Posts: 3357
Location: Tucson AZ
I believe that was specifically about prefab modular/mobile homes because the exterior walls are built on top of it and could cause a structural problem.

_________________
Stephen Perrera
Top Floor Installation Co.
Tucson, Arizona
IFCII Certified Inspector
Floor Repairs and Installation in Tucson, Az
http://www.tucsonazflooring.com

Top
 Profile E-mail  
 
Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 

Board index » Hardwood Flooring » General Hardwood Flooring

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group

phpBB SEO